bp50-005 thru bp50-10 page: 1 frontier electronics corp. 667 e. cochran street, simi valley, ca 93065 tel: (805) 522-9998 fax: (805) 522-9989 e-mail: frontiersales@frontierusa.com web: http://www.frontierusa.com 50a high current silicon bridge rectifiers bp50-005 thru bp50-10 features z current rating 50a z reverse voltage rating up to 1000v z typical ir less than 1 a z high temperature soldering guaranteed: 260c /10 second mechanical data z case: metal heat sink ca se, electrically insulated dimensions in inches and (millimeters) z terminals: universal .25? (6.3mm) fast on z mounting method: bolt down on heat sink with silicon thermal compound between bridge and mounting surface for maximum heat transfer efficiency z weight : 20 grams dim min max remark h* 0.295(7.5) 0.311(7.9) suffix ?s? thin case i* 0.74(18.80) 0.84(21.30) suffix ?s? thin case l* 1.09(27.89) - suffix ?s? thin case maximum ratings and electrical characteristics ratings at 25 c ambient temperature unless otherwise specified single phase, half wave, 60 hz, resistive or inductive load. for capacitive load, derate current by 20% ratings symbol bp50-005 BP50-01 bp50- 02 bp50-04 bp50-06 bp50-08 bp50-10 units maximum recurrent peak reverse voltage v rrm 50 100 200 400 600 800 1000 v maximum rms voltage v rms 35 70 140 280 420 560 700 v maximum dc blocking voltage v dc 50 100 200 400 600 800 1000 v maximum average forward rectified output current at tc=55 c i o 50.0 a peak forward surge current single sine-wave superimposed on rated load i fsm 550 a storage temperature range t stg - 55 to + 175 oc operating temperature range t op - 55 to + 175 oc electrical characteristics (a t t a =25 c unless otherwise noted) characteristics symbol bp50-005 BP50-01 bp50-02 bp50-04 bp50-06 bp50-08 bp50-10 units maximum instantaneous forward voltage per bridge element at specified current v f 1.1 v maximum reverse dc current at rate dc blocking voltage per element i r 10 a note: suffix no. versus different cases and terminals case suffix no terminal normal metal case thin metal case normal plastic case aluminum base thin plastic case aluminum base fast on terminals no suffix s p ps wire lead terminals w ws pw pws in line pin configuration l ls 1.13(28.7) 1.12(28.4) 0.469(11.90) 0.429(10.90) 0.752(19.10) 0.673(17.10) l* 1.200 (30.5) min 0.042(1.07) 0.038(0.97) h* 0.442(11.23) 0.432 ( 10.97 ) 0.094 (2.4) diam i* 1.00(25.40) 0.90(22.86) 0.25 (6.35) 0.565(14.35) 0.525(13.35) 1.13(28.7) 1.12(28.4) 0.657(16.7) 0.618(15.7) 0.652 (16.6) 0.728(18.5) 0.689 ( 17.5 ) hole for no.10 screw 0.2? (5.08)diam. h* 0.442(11.23) 0.432(10.97) hole for no.10 screw 0.2? (5.08)diam.
bp50-005 thru bp50-10 page: 2 ratings and characteristic curves bp50-005 thru bp50-10 fig 1 maximum output rectified current 50 45 40 35 30 25 20 15 10 5 0 average forward output current, amperes 20 40 60 80 100 120 140 160 180 case temperature t c fig 2 typical reverse characteristics at t j =25oc 10 1.0 0.1 .01 instantaneous reverse current microamperes 0 20 40 60 80 100 120 140 percent of rated peak reverse voltage fig 4 maximum non-repetitive peak forward surge current 600 400 300 200 100 40 peak forward surge current, amperes 1 1.5 2 3 4 5 6 7 8 910 15 20 30 4050 70 100 number of cycles at 60h z t j =175oc single sine wave (jedec method) fig 3 typical instantaneous forward characteristics 1000 500 100 50 10 5 1.0 0.1 instantaneous forward current, amperes 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 instantaneous forward voltage, volts t j =25oc pulse width 300us 1% duty cycle bp50-l in line pin configuration (plastic case) ac .442 11.23 .432 10.97 .140 3.6 .120 3.05 .040 28.7 1.12 13.9
|
